| Naslov: | Investigation of the best manufacturing orientation of Co-Cr-W-Si dental prosthetic elements in the selective laser melting process |
|---|
| Avtorji: | ID Pal, Snehashis (Avtor)
ID Gotlih, Janez (Avtor)
ID Drstvenšek, Igor (Avtor) |
|---|
| Datoteke: |  ams_ams-202202-0005.pdf (640,47 KB)
MD5: 51AF345899C86E0CA9DC275432B5A1AE
 https://www.actamechanica.sk/artkey/ams-202202-0005_investigation-of-the-best-manufacturing-orientation-of-co-cr-w-si-dental-prosthetic-elements-in-the-selective-l.php
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
|
|---|
| Opis: | It is well known that Selective Laser Melting (SLM) does not provide the same mechanical
properties in all directions of the part. This is due to the microstructural grain orientation and
pore shape in SLM products. Therefore, depending on the direction of the pressure applied to the
SLM product, a different manufacturing orientation is required to achieve the best mechanical
properties. Changing the microstructural grain orientation is difficult through SLM, but a process
to reduce the size and number of the pores can be discovered through different combinations
of manufacturing parameters. In prosthodontics, pressure is usually applied in the vertical
direction, which leads to compression and bending of crowns with bridges. The compressive
load can be easily absorbed in the crowns, but the bending force has a significant effect here.
Therefore, a product with high tensile strength and high ductility is needed to survive longer.
Considering these requirements, this study determined the best parameters for laser processing
by SLM method to reduce porosity and improve mechanical strength and ductility of Co-CrW-Si alloy products. The result is a relative product density of 100% for cubic specimens and a
yield strength, ultimate tensile strength, and elongation at break of the tensile specimens of 900
MPa, 1200 MPa, and 15%, respectively, obtained in specimen build-up in the Z direction with a
laser power of 60 W and a scanning speed of 450 mm/s. Eventually, the best orientation for the
production of dental prosthetic elements using the SLM process was determined. |
|---|
| Ključne besede: | cobalt-chromium alloy, dental implant, density, tensile strength, ductility, selective laser melting |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 08.01.2022 |
|---|
| Datum sprejetja članka: | 11.01.2022 |
|---|
| Datum objave: | 01.06.2022 |
|---|
| Založnik: | Acta Mechanica Slovaca |
|---|
| Leto izida: | 2022 |
|---|
| Št. strani: | str. 30-35 |
|---|
| Številčenje: | Ročnik 26, 2 |
|---|
| PID: | 20.500.12556/DKUM-89300  |
|---|
| UDK: | 658.5:616.31 |
|---|
| COBISS.SI-ID: | 200455683 |
|---|
| DOI: | 10.21496/ams.2023.003 |
|---|
| ISSN pri članku: | 1335-2393 |
|---|
| Datum objave v DKUM: | 03.07.2024 |
|---|
| Število ogledov: | 212 |
|---|
| Število prenosov: | 33 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
