| Naslov: | Empirical modeling of transverse displacements of single-sided transversely cracked prismatic tension beams |
|---|
| Avtorji: | ID Skrinar, Matjaž (Avtor) |
|---|
| Datoteke: |  modelling-03-00031-v2.pdf (1,65 MB)
MD5: 9C454335AAEE5671511EAB70706756C2
 https://www.mdpi.com/2673-3951/3/4/31
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FGPA - Fakulteta za gradbeništvo, prometno inženirstvo in arhitekturo
|
|---|
| Opis: | While the effects of axial compression on beams have long been known, the effect of tensile
axial loads on one-sided transversely cracked beams is less known. The crack namely shifts the
position of the resultant of the axial normal stresses deeper into the uncracked part of the cross-section,
and the crack tends to open, causing a transverse displacement. Therefore, this paper focuses on
empirical modeling of the considered phenomenon for slender prismatic beams in order to establish
a suitable 1D computational model based on detailed 3D FE mesh results. This goal can be achieved
through the already established simplified model, where the crack is represented by an internal hinge
endowed with a rotational spring. Several analyses of various beams differing in geometry, crack
locations, and boundary conditions were executed by implementing 3D FE meshes to establish the
appropriate model’s bending governing differential equation. After that, the corresponding parameter
definitions were calibrated from the database of 3D FE models. By redefining the model’s input
parameters, a suitable solution is achieved, offering a good balance between the results’ accuracy and
the required computational effort. The functionality of the newly obtained solutions was verified
through some comparative case studies that supplement the derivations. |
|---|
| Ključne besede: | transverse cracks, axial tensile forces, simplified model of crack, transverse displacements |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 09.11.2022 |
|---|
| Datum sprejetja članka: | 12.12.2022 |
|---|
| Datum objave: | 16.12.2022 |
|---|
| Založnik: | MDPI AG |
|---|
| Leto izida: | 2022 |
|---|
| Št. strani: | str. 481-498 |
|---|
| Številčenje: | Vol. 3, iss. 4 |
|---|
| PID: | 20.500.12556/DKUM-92046  |
|---|
| UDK: | 624.072.2:519.85 |
|---|
| COBISS.SI-ID: | 146437891 |
|---|
| DOI: | 10.3390/modelling3040031 |
|---|
| ISSN pri članku: | 2673-3951 |
|---|
| Avtorske pravice: | © 2022 by the author. |
|---|
| Datum objave v DKUM: | 13.03.2025 |
|---|
| Število ogledov: | 158 |
|---|
| Število prenosov: | 9 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
