| Naslov: | Mechanisms of defect formation in Ti-6Al-4V product during re-melting of layers in selective laser melting |
|---|
| Avtorji: | ID Pal, Snehashis (Avtor)
ID Finšgar, Matjaž (Avtor)
ID Hudak, Radovan (Avtor)
ID Rajtukova, Viktoria (Avtor)
ID Brajlih, Tomaž (Avtor)
ID Gubeljak, Nenad (Avtor)
ID Drstvenšek, Igor (Avtor) |
|---|
| Datoteke: |  1-s2.0-S1526612523008976-main.pdf (16,16 MB)
MD5: 88725B14A301641103E72F22988F2FF9
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
FKKT - Fakulteta za kemijo in kemijsko tehnologijo
|
|---|
| Opis: | Knowledge of defect formation mechanisms in the manufacturing process helps improve product quality. In this study, defect formation due to re-melting of each layer in selective laser melting of Ti-6Al-4V demonstrated the physical behavior in the manufacture of metallic parts. The re-melting strategy was based on scanning with low energy density (ED) and increased ED with various combinations of laser processing parameters. The increased EDs and their parameters, namely laser power, scanning speed, and hatch distance, were selected based on the previous research experience by the authors. The concept of selecting a low ED followed by a high ED was to reduce the spattering of the powder material during the process. The low ED caused partial sintering of the powder, while the high ED caused the melting of the material, resulting in different metallurgical properties of the manufactured parts. Densities, pore properties, porosity in the initial layers, surface morphologies, and microstructures in the defective areas of the samples were studied to determine the effects of re-melting. Advantages and disadvantages were found with respect to the range of applications of the products |
|---|
| Ključne besede: | re-melting, pore properties, defect, surface morphology, Ti-6Al-4V, selective laser melting |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 02.09.2023 |
|---|
| Datum sprejetja članka: | 16.09.2023 |
|---|
| Datum objave: | 22.09.2023 |
|---|
| Leto izida: | 2023 |
|---|
| Št. strani: | str. 260-275 |
|---|
| Številčenje: | Vol. 105 |
|---|
| PID: | 20.500.12556/DKUM-92144  |
|---|
| UDK: | 620.1/.2 |
|---|
| COBISS.SI-ID: | 166689539 |
|---|
| DOI: | 10.1016/j.jmapro.2023.09.044 |
|---|
| ISSN pri članku: | 2212-4616 |
|---|
| Avtorske pravice: | © 2023 The Authors |
|---|
| Datum objave v DKUM: | 14.03.2025 |
|---|
| Število ogledov: | 169 |
|---|
| Število prenosov: | 16 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
