| Naslov: | Effect of presetting and deep rolling on creep of torsion spring bars |
|---|
| Avtorji: | ID Močilnik, Vinko (Avtor)
ID Gubeljak, Nenad (Avtor)
ID Predan, Jožef (Avtor) |
|---|
| Datoteke: |  68f8dad902583.pdf (2,40 MB)
MD5: 1E2940C065EAFC97C4DC360FFDD2C900
 https://www.sv-jme.eu/sl/article/effect-of-presetting-and-deep-rolling-on-creep-of-torsion-bars/
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
|
|---|
| Opis: | This study investigates the creep behavior of torsion spring bars by combining experimental testing and numerical modeling. Experimental investigations were performed on torsional specimens subjected to different presetting levels and deep rolling surface treatments, showing different effects on stress relaxation at a constant torsion angle. Finite element method (FEM) simulations incorporating elasto-visco-plastic material behavior successfully reproduced the time-dependent deformation observed experimentally. Material parameters for the FEM model were derived from experimental data. The findings show that a two-stage presetting process combined with intermediate deep rolling results in higher residual compressive stresses in the surface layers compared to a single-stage presetting process. Although this method aims to mitigate creep under constant loading conditions, its effectiveness is limited. A reduction in creep strains is only observed up to a presetting level of approximately 4.3 %; above this threshold, creep strains increase significantly and loading capacity decreases. |
|---|
| Ključne besede: | creep, torsion bar, FEM analyzis, presetting, deep rolling, torque, twist angle |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 26.05.2025 |
|---|
| Datum sprejetja članka: | 27.08.2025 |
|---|
| Založnik: | Univerza v Ljubljani, Fakulteta za strojništvo |
|---|
| Leto izida: | 2025 |
|---|
| Št. strani: | str. 301-308 |
|---|
| Številčenje: | Vol. 71, no. 9/10 |
|---|
| PID: | 20.500.12556/DKUM-96195  |
|---|
| UDK: | 539.414:519.6 |
|---|
| COBISS.SI-ID: | 259515651 |
|---|
| DOI: | 10.5545/sv-jme.2025.1407 |
|---|
| ISSN pri članku: | 2536-3948 |
|---|
| Datum objave v DKUM: | 09.12.2025 |
|---|
| Število ogledov: | 121 |
|---|
| Število prenosov: | 8 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
