| Naslov: | Microstructure and properties after friction stir processing of twin-roll cast Al–Mn–Cu–Be alloy |
|---|
| Avtorji: | ID Macerl, Matjaž (Avtor)
ID Zupanič, Franc (Avtor)
ID Hočuršćak, Lara (Avtor)
ID Klobčar, Damjan (Avtor)
ID Kovács, Andras (Avtor)
ID Bončina, Tonica (Avtor) |
|---|
| Datoteke: |  crystals-12-00630.pdf (30,49 MB)
MD5: 506BEE834991309CBFCFCE0D3EF11FB3
 https://www.mdpi.com/2073-4352/12/5/630
http://dx.doi.org/10.3390/cryst12050630
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
|
|---|
| Opis: | We studied the effect of friction stir processing (FSP) on the microstructure and properties of high-speed twin-roll cast strips made of an experimental Al–Mn–Cu–Be alloy. The samples were examined using light, scanning, and transmission electron microscopy, microchemical analysis, X-ray diffraction, and indentation testing. During FSP, the rotational speed varied, while other parameters remained constant. The uniformity of the microstructure increased with the growing rotational speed. In the stir zone, several processes took place, and the most important were: recrystallisation of the matrix grains, fragmentation of the primary intermetallic particles Al▫$_{15}$▫Mn▫$_{3}$▫Be▫$_{2}$▫ and their more uniform distribution in the stir zone, fracture, and dispersion of the eutectic icosahedral quasicrystalline phase (IQC), transformation of tiny Al▫$_{15}$▫Mn▫$_{3}$▫Be▫$_{2}$▫ and IQC particles into the τ▫$_{1}$▫-Al▫$_{26}$▫Mn▫$_{6}$▫Cu▫$_{4}$▫ phase and precipitation of Al–Mn–Cu precipitates. In the thermomechanically affected zone, new dislocations formed as well as dispersion of the IQC eutectic phase and recrystallisation of the matrix grains. In the heat-affected zone, dissolution of θ’-Al▫$_{2}$▫Cu precipitates occurred. The hardness variation was not severe between the stir and heat-affected zones. |
|---|
| Ključne besede: | litje, mikrostruktura, obdelava s trenjem in mešanjem, trdota, preobrazba, aluminij, casting, microstructure, friction stir processing, hardness, transformation, aluminium |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 30.03.2022 |
|---|
| Datum sprejetja članka: | 25.04.2022 |
|---|
| Datum objave: | 27.04.2022 |
|---|
| Založnik: | MDPI |
|---|
| Leto izida: | 2022 |
|---|
| Št. strani: | 18 str. |
|---|
| Številčenje: | ǂVol. ǂ12, ǂiss. ǂ5 (630) |
|---|
| PID: | 20.500.12556/DKUM-96353  |
|---|
| UDK: | 669.2/.8:620.1 |
|---|
| COBISS.SI-ID: | 106703363 |
|---|
| DOI: | 10.3390/cryst12050630 |
|---|
| ISSN pri članku: | 2073-4352 |
|---|
| Datum objave v DKUM: | 03.04.2026 |
|---|
| Število ogledov: | 198 |
|---|
| Število prenosov: | 6 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
