| Naslov: | Experimental and numerical investigation of the deep drawing process using a tractrix die – an industrial case study focused on stress and temperature analysis |
|---|
| Avtorji: | ID Mandić, Vesna (Avtor)
ID Milosavljevic, Dj. (Avtor)
ID Jurković, Zoran (Avtor)
ID Adamovic, D. (Avtor) |
|---|
| Datoteke: |  APEM19-1_133-148.pdf (1,74 MB)
MD5: 6C07C805EC6438ACEBDF032438EC0B23
 https://apem-journal.org/Archives/2024/Abstract-APEM19-1_133-148.html
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
|
|---|
| Opis: | The deep drawing process of thick sheet metal for vessel production is carried out by applying a tractrix die with the absence of a blank holder, which has economic benefits for industrial production. The main aim of the paper is the development of a reliable numerical thermo-mechanical model of a silicon brass vessel manufactured by a deep drawing process in a tractrix die and a subsequent ironing process, which includes the previous assembly of the dies with reinforcing rings that creates the required prestresses. The testing of the mechanical properties of silicon brass CuZn24Si was carried out by a standard uniaxial tensile test, thus a flow curve was determined to describe the material behaviour. The initial temperatures of the environment, blank and tools were measured with an infrared thermal imager. A comprehensive finite element stress analysis of the deformable tools was carried out for the assembly phase of the dies, and for workpiece and tools in the deep drawing and ironing processes. The comparison of measured and numerically estimated temperatures had a good agreement, so the developed numerical model was confirmed and validated. This research study demonstrates how different process parameters can be investigated through a reliable and precise numerical model with complementary experimental research for the optimization of industrial technology. |
|---|
| Ključne besede: | deep drawing, tractrix die, reinforcing rings, finite element method, FEM, experimental-numerical approach, numerical modelling, simulation, infrared imaging technology, simufact.forming |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 28.12.2023 |
|---|
| Datum sprejetja članka: | 01.03.2024 |
|---|
| Datum objave: | 29.04.2024 |
|---|
| Založnik: | Chair of Production Engineering (CPE), University of Maribor Faculty of Mechanical Engineering |
|---|
| Leto izida: | 2024 |
|---|
| Št. strani: | str. 133-148 |
|---|
| Številčenje: | Vol. 19, no. 1 |
|---|
| PID: | 20.500.12556/DKUM-96816  |
|---|
| UDK: | 658.562 |
|---|
| COBISS.SI-ID: | 266558979 |
|---|
| DOI: | 10.14743/apem2024.1.498 |
|---|
| ISSN pri članku: | 1854-6250 |
|---|
| Datum objave v DKUM: | 29.01.2026 |
|---|
| Število ogledov: | 159 |
|---|
| Število prenosov: | 2 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
