| Naslov: | Integrated production and maintenance policy for manufacturing systems prone to products' quality degradation |
|---|
| Avtorji: | ID BouAbid, H. (Avtor)
ID Dhouib, K. (Avtor)
ID Gharbi, A. (Avtor) |
|---|
| Datoteke: |  APEM19-4_512-526.pdf (2,11 MB)
MD5: 7C8D565EC1927D6623233D3BFF38FBBC
 https://apem-journal.org/Archives/2024/Abstract-APEM19-4_512-526.html
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
|
|---|
| Opis: | This paper proposes an integrated production planning and preventive maintenance strategy for manufacturing systems prone to quality degradation. The production planning focus on the regulation of production rates and the sizing of finished product’s safety stock to meet costumer’s demand. The safety stock is built to palliate shortages when the manufacturing operation begins generating non-conforming products and is shutdown to perform restoration action. In the other hand, preventive maintenance activities are also planned to minimise the quantity of non-conforming products. Mathematical models are proposed and consider all sub-policies and scenarios contingent on the production control policy as well as the entire range of possible values for the safety stock level. A numerical procedure has been established to ascertain the optimal integrated policy, aiming to minimize the total accrued cost per time unit along an infinite horizon. A simulation model has also been created to check and validate the analytical results. Finally, a comparative analysis is presented to prove that the proposed joint policy outperforms other strategies considered in the literature and practice and can result in substantial economic gains. |
|---|
| Ključne besede: | production planning, stock control, preventive maintenance, quality degradation, hedging point policy, analytical modelling, simulation analysis |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 12.12.2023 |
|---|
| Datum sprejetja članka: | 15.12.2024 |
|---|
| Datum objave: | 30.12.2024 |
|---|
| Založnik: | Chair of Production Engineering (CPE), University of Maribor Faculty of Mechanical Engineering |
|---|
| Leto izida: | 2024 |
|---|
| Št. strani: | str. 512-526 |
|---|
| Številčenje: | Vol. 19, no. 4 |
|---|
| PID: | 20.500.12556/DKUM-96940  |
|---|
| UDK: | 658.562 |
|---|
| COBISS.SI-ID: | 267240963 |
|---|
| DOI: | 10.14743/apem2024.4.521 |
|---|
| ISSN pri članku: | 1854-6250 |
|---|
| Avtorske pravice: | Content from this work may be used under the terms of the Creative Commons Attribution 4.0 International Licence (CC BY 4.0). Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI. |
|---|
| Datum objave v DKUM: | 04.02.2026 |
|---|
| Število ogledov: | 190 |
|---|
| Število prenosov: | 1 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
