| Naslov: | Impact of Cobot parameters on the worker productivity : optimization challenge |
|---|
| Avtorji: | ID Javernik, Aljaž (Avtor)
ID Buchmeister, Borut (Avtor)
ID Ojsteršek, Robert (Avtor) |
|---|
| Datoteke: |  APEM17-4_494-504.pdf (1,59 MB)
MD5: 75B1BE4C72F9BF0471B1D95050114E0B
 https://apem-journal.org/Archives/2022/APEM17-4_494-504.pdf
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
|
|---|
| Opis: | In the era of Industry 4.0 and the introduction of new technologies, collaborative workplaces represent the potential to increase the efficiency of manufacturing systems. The presented research focuses on studying the impact of changing the speed and acceleration of a Cobot to the number of finished products at a collaborative workstation, the average assembly time, and the utilization of the Cobot and worker. In a laboratory experiment, it was demonstrated that changing the parameters of the Cobot significantly affects the optimization parameters of the collaborative workstation productivity. The results indicate an increase in production capacity with an increase in the speed and acceleration of the Cobot, while at the same time highlighting the importance of uniform utilization and occupancy of the Cobot and worker. The findings are particularly interesting from the influence of the Cobot’s audio and video effects on worker, when reducing the average assembly time while increasing the Cobot's capabilities. The results and findings presented open up important new areas of research in the field of social, time and financial justification of collaborative workplaces. |
|---|
| Ključne besede: | collaborative robot, cobot, collaborative operation, robot parameters, worker productivity, working scenarios, manufacturing efficiency, optimization |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 10.09.2022 |
|---|
| Datum sprejetja članka: | 22.12.2022 |
|---|
| Datum objave: | 30.12.2022 |
|---|
| Založnik: | Chair of Production Engineering (CPE), University of Maribor Faculty of Mechanical Engineering |
|---|
| Leto izida: | 2022 |
|---|
| Št. strani: | str. 494-504 |
|---|
| Številčenje: | Vol. 17, no. 4 |
|---|
| PID: | 20.500.12556/DKUM-97200  |
|---|
| UDK: | 658.5:004.5 |
|---|
| COBISS.SI-ID: | 137243139 |
|---|
| DOI: | 10.14743/apem2022.4.451 |
|---|
| ISSN pri članku: | 1854-6250 |
|---|
| Avtorske pravice: | Content from this work may be used under the terms of the Creative Commons Attribution 4.0 International Licence (CC BY 4.0). Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI. |
|---|
| Datum objave v DKUM: | 23.02.2026 |
|---|
| Število ogledov: | 138 |
|---|
| Število prenosov: | 9 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
