| Naslov: | Modeling and optimization of finish diamond turning of spherical surfaces based on response surface methodology and cuckoo search algorithm |
|---|
| Avtorji: | ID Kramar, Davorin (Avtor)
ID Cica, Djordje (Avtor) |
|---|
| Datoteke: |  APEM16-3_326-334.pdf (1,26 MB)
MD5: 11E8722D071F430638146B36F8901627
 https://apem-journal.org/Archives/2021/APEM16-3_326-334.pdf
http://apem-journal.org/Archives/2021/Abstract-APEM16-3_326-334.html
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
|
|---|
| Opis: | Surface roughness is one of the most significant factors to indicate the prod- uct quality. Diamond turning is an efficient and highly accurate material re- moval process to improve the surface quality of the workpiece. In the present study, the arithmetic mean absolute roughness (Ra) and total height of profile (Rt) of spherical surface during finish turning of a commercial brass alloy CuZn40Pb2 were modeled using Response Surface Methodology (RSM). The experimental investigations were carried out using the Central Composite Design (CCD) under dry conditions. The effect of cutting parameters such as spindle speed, feed rate and depth of cut) on spherical surface quality was analyzed using analysis of variance (ANOVA). A cuckoo search (CS) algorithm was used to determine the optimum machining parameters to minimize the surface roughness. Finally, confirmation experiments were carried out to verify the adequacy of the considered optimization algorithm. |
|---|
| Ključne besede: | brass alloy, diamond turning, surface roughness, spherical surface, modeling, optimization, response surface methodology, cuckoo search |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 31.05.2021 |
|---|
| Datum sprejetja članka: | 15.09.2021 |
|---|
| Datum objave: | 31.10.2021 |
|---|
| Založnik: | Chair of Production Engineering (CPE), University of Maribor Faculty of Mechanical Engineering |
|---|
| Leto izida: | 2021 |
|---|
| Št. strani: | str. 326-334 |
|---|
| Številčenje: | Vol. 16, no. 3 |
|---|
| PID: | 20.500.12556/DKUM-97374  |
|---|
| UDK: | 621.941:669.35 |
|---|
| COBISS.SI-ID: | 87359491 |
|---|
| DOI: | 10.14743/apem2021.3.403 |
|---|
| ISSN pri članku: | 1854-6250 |
|---|
| Avtorske pravice: | Content from this work may be used under the terms of the Creative Commons Attribution 4.0 International Licence (CC BY 4.0). Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI. |
|---|
| Datum objave v DKUM: | 02.03.2026 |
|---|
| Število ogledov: | 132 |
|---|
| Število prenosov: | 4 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
