| Naslov: | Experimental and numerical thermo-mechanical characterization of polylactic acid fabricated by fused filament fabrication |
|---|
| Avtorji: | ID Hanželič, Blaž (Avtor)
ID Nečemer, Branko (Avtor)
ID Glodež, Srečko (Avtor)
ID Harih, Gregor (Avtor) |
|---|
| Datoteke: |  https://4spepublications.onlinelibrary.wiley.com/doi/10.1002/pen.70610
 Polymer_Engineering__Sci_-_2026_-_Experimental_and_Numerical_Thermo‐Mechanical_Characterization_of_Polylactic.pdf (2,08 MB)
MD5: C24C7FED385D3D2CF94F01B4B2C50A84
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
|
|---|
| Opis: | This study investigates the thermomechanical response of polylactic acid (PLA) specimens fabricated by fused filament fabrication (FFF) at two nozzle temperatures (190°C and 230°C), while mechanical testing was performed at three temperatures (20°C, 30°C, and 40°C) below the glass transition temperature (Tg). Quasi-static uniaxial tensile and compression tests were conducted to characterize the mechanical response under these thermal conditions. The experimental results showed that increasing nozzle temperature improved tensile stiffness and strength. The highest tensile and compressive properties were obtained for specimens printed at 230°C and tested at 20°C, with tensile modulus and tensile strength of 3573 MPa and 54 MPa, and compressive modulus and compressive strength of 1343 MPa and 71 MPa, respectively, indicating anisotropic mechanical behavior. In addition, dynamic mechanical thermal analysis (DMTA) was also performed to evaluate the viscoelastic response and determine Tg, including a comparison with injection-molded PLA. To establish a reliable predictive framework for thermomechanical behavior, experimental measurements were used to calibrate the ANSYS-Three Network Model (TNM). The resulting numerical simulations of the tensile and compression tests demonstrated good agreement with the experimental results, confirming the capability of the model to predict the thermomechanical response of polylactic acid fabricated by fused filament fabrication. |
|---|
| Ključne besede: | Ansys-three network model, dynamic mechanical thermal analysis, fused filament fabrication, polylactic acid, thermomechanical characterization |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Datum objave: | 18.05.2026 |
|---|
| Založnik: | Wiley |
|---|
| Leto izida: | 2026 |
|---|
| Št. strani: | 16 str. |
|---|
| PID: | 20.500.12556/DKUM-98163  |
|---|
| UDK: | 531:004.8 |
|---|
| COBISS.SI-ID: | 278555907 |
|---|
| DOI: | 10.1002/pen.70610 |
|---|
| ISSN pri članku: | 1548-2634 |
|---|
| Datum objave v DKUM: | 21.05.2026 |
|---|
| Število ogledov: | 306 |
|---|
| Število prenosov: | 18 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
