| Naslov: | Mechanism-based comparison of Ti-6Al-4V lattice topologies with and without face sheets under quasi-static and dynamic loading |
|---|
| Avtorji: | ID Bin Riaz, Muhammad Arslan (Avtor)
ID Ren, Zoran (Avtor)
ID Rikić, Aleksej (Avtor)
ID Güden, Mustafa (Avtor) |
|---|
| Datoteke: |  Mechanism-based_compariso-Arslan_Bin_Riaz-2026.pdf (21,75 MB)
MD5: CA37F528068C1D724C16D6691AEADAC8
 https://www.sciencedirect.com/science/article/pii/S277281022600022X?via%3Dihub
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
|
|---|
| Opis: | A constitutive model calibrated for an electron-beam-melted Ti-6Al-4V Body-Centred Cubic (BCC) lattice was modelled to evaluate nine strut-based lattice topologies different strain rates. For each topology, configurations with face sheets (WFS) and without face sheets (WOFS) were compared using the first-peak stress, ultimate compressive stress (UCS), plateau stress, and specific energy absorption (SEA) performance indicators. The model was initially validated against experiments for a WFS BCC lattice and then used to predict performance across the remaining designs. Face sheet efficiency factors were introduced to quantify the mass-normalised benefit or penalty of face sheets for each topology, including peak stress, UCS, plateau stress, and SEA. The highest SEA under quasi-static loading was obtained for Face-Body-Centred-Cubic (FBCC)–WOFS, while under dynamic impact, the highest SEA was achieved by Face-Body-Centred-Cubic with stiffener in Z direction (FBCCz)–WOFS, closely followed by Octet–WOFS. Face-Body-Centred-Cubic stiffeners in x, y and z directions (FBCCxyz) exhibited the highest strength response. Collapse was classified into four dominant modes. Shear collapse encouraged load redistribution, mixed (shear–global) collapse rendered homogenous deformation, global failure showed the highest crushing force efficiency, and layer-wise collapse resulted in higher peak stresses. |
|---|
| Ključne besede: | strut-based lattices, numerical modelling, lattice topology comparison, drop-weight impact, specific energy absorption, facesheet efficiency matrices |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 26.03.2026 |
|---|
| Datum sprejetja članka: | 23.06.2026 |
|---|
| Datum objave: | 13.07.2026 |
|---|
| Založnik: | Elsevier |
|---|
| Leto izida: | 2026 |
|---|
| Št. strani: | 20 str. |
|---|
| Številčenje: | Letn. 4, št. članka 100145 |
|---|
| PID: | 20.500.12556/DKUM-99282  |
|---|
| UDK: | 531/533:620.1 |
|---|
| COBISS.SI-ID: | 284701187 |
|---|
| DOI: | 10.1016/j.smmf.2026.100145 |
|---|
| ISSN pri članku: | 2772-8102 |
|---|
| NUK URN: | URN:SI:UM:DK:9ZMJ6WE2 |
|---|
| Datum objave v DKUM: | 11.08.2026 |
|---|
| Število ogledov: | 324 |
|---|
| Število prenosov: | 17 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
