| | SLO | ENG | Cookies and privacy

Bigger font | Smaller font

Show document Help

Title:POSODOBITEV VPENJANJA ORODIJ ZA BRIZGANJE GUMENIH IZDELKOV
Authors:ID Kralj, Mihael (Author)
ID Pahole, Ivan (Mentor) More about this mentor... New window
ID Čuš, Franc (Comentor)
Files:.pdf VS_Kralj_Mihael_2010.pdf (4,56 MB)
MD5: 3D3710EF71AC93B1CE3177F73D0DA46F
PID: 20.500.12556/dkum/b5ca14d9-5b96-4e93-805e-d5b2caeb9cdf
 
Language:Slovenian
Work type:Undergraduate thesis
Organization:FS - Faculty of Mechanical Engineering
Abstract:Predstavljen je novi sistem vpenjanja na injekcijskih stiskalnicah. Ta sistem nadomesti ročno privijanje orodja na stiskalnico, s čimer lahko prihranimo veliko časa. Vijake za pritrditev orodja nadomestijo magnetne plošče, katere sprožimo s pritiskom na gumb in tako vpnejo orodje. Za pritrditev izmetalnih ploskev, namesto vijakov uporabimo vpenjalne klinaste elemente, ki delujejo pod hidravličnim tlakom. S pomočjo teh dveh sistemov, lahko orodje namestimo in vpnemo veliko hitreje. To pa nam omogoča tudi predgrevanje orodja v posebni peči, saj ni vključenega neposrednega človeškega faktorja pri montaži orodja. Ker je čas menjave orodja kratek, se nam orodje pri montaži ohladi le minimalno, kar pa nadomestimo z dogrevanjem orodja na stiskalnici. Zelo pomembno je tudi, da je montaža orodja veliko bolj prijazna in varna.
Keywords:brizganje gumenih izdelkov, preoblikovalna orodja, stiskalnice, vpenjanje
Place of publishing:Maribor
Publisher:[M. Kralj]
Year of publishing:2010
PID:20.500.12556/DKUM-13796 New window
UDC:621.881:621.979(043.2)
COBISS.SI-ID:14163222 New window
NUK URN:URN:SI:UM:DK:0YK21OW8
Publication date in DKUM:06.05.2010
Views:2539
Downloads:369
Metadata:XML DC-XML DC-RDF
Categories:KTFMB - FS
:
Copy citation
  
Average score:(0 votes)
Your score:Voting is allowed only for logged in users.
Share:Bookmark and Share



Hover the mouse pointer over a document title to show the abstract or click on the title to get all document metadata.

Secondary language

Language:English
Title:TOOL CLAMPING MODERNIZATION FOR INJECTION OF RUBBER PRODUCTS
Abstract:A new clamping system for molding injection presses is presented. This system replaces manual screwing of the tools in the press, which enables enormous time savings. Screws for mounting tools were replaced by magnetic plates that are activated by pressing a button, and thus clamping the tool. For the mounting of ejection plates instead of screws clamping wedge elements are used, which are operating under hydraulic pressure. With the help of these two systems the tools can be installed and clamped much faster. This on the other hand allows us pre-heating of the tools in a special oven, as there is no direct human element involved in the mounting of the tools. As for the replacement of the tools little time is required, the tools during mounting cool off only by a minimum, the loss of heat is replaced by the heating system in the press. It is also very important that the mounting of the tool is much more friendly and safe.
Keywords:injection molding of rubber products, reshaping tools, pressing machines, clamping


Comments

Leave comment

You must log in to leave a comment.

Comments (0)
0 - 0 / 0
 
There are no comments!

Back
Logos of partners University of Maribor University of Ljubljana University of Primorska University of Nova Gorica