| Naslov: | Personalizing human–robot workplace parameters in human-centered manufacturing |
|---|
| Avtorji: | ID Ojsteršek, Robert (Avtor)
ID Buchmeister, Borut (Avtor)
ID Javernik, Aljaž (Avtor) |
|---|
| Datoteke: |  machines-12-00546-v2.pdf (5,12 MB)
MD5: 05CEEA53031A74050FC78B5A7FD65AFC
 https://www.mdpi.com/2075-1702/12/8/546
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
|
|---|
| Opis: | This study investigates the relationship between collaborative robot (CR) parameters and worker utilization and system performance in human–robot collaboration (HRC) environments. We investigated whether optimized parameters increase workplace efficiency and whether adapting these parameters to the individual worker improves workplace outcomes. Three experimental scenarios with different CR parameters were analyzed in terms of the setup time, assembly time, finished products, work in process, and worker utilization. The main results show that personalized CR parameters significantly improve efficiency and productivity. The scenario in which CR parameters were tailored to individual workers, balanced the workload, and minimized worker stress, resulting in higher productivity compared to non-people-centric settings. The study shows that personalization reduces cognitive and physical stress, promotes worker well-being, and is consistent with the principles of human-centered manufacturing. Overall, our research supports the adoption of personalized, collaborative workplace parameters, supported by the mathematical model, to optimize employee efficiency and health, contributing to human-centered and efficient HRC environments. |
|---|
| Ključne besede: | human–robot workplace, collaborative workplace, human-centered manufacturing, stress index, modelling, efficiencxy |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 08.07.2024 |
|---|
| Datum sprejetja članka: | 09.08.2024 |
|---|
| Datum objave: | 11.08.2024 |
|---|
| Založnik: | MDPI |
|---|
| Leto izida: | 2024 |
|---|
| Št. strani: | 16 str. |
|---|
| Številčenje: | Vol. 12, iss. 8, [article no.] 546 |
|---|
| PID: | 20.500.12556/DKUM-90423  |
|---|
| UDK: | 658.5 |
|---|
| COBISS.SI-ID: | 204299779 |
|---|
| DOI: | 10.3390/machines12080546 |
|---|
| ISSN pri članku: | 2075-1702 |
|---|
| Avtorske pravice: | © 2024 by the authors |
|---|
| Datum objave v DKUM: | 03.09.2024 |
|---|
| Število ogledov: | 203 |
|---|
| Število prenosov: | 37 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
