| Title: | The influence of the rolling direction on the mechanical properties of the Al-Alloy EN AW-5454-D |
|---|
| Authors: | ID Balant, Matjaž (Author)
ID Vuherer, Tomaž (Author)
ID Majerič, Peter (Author)
ID Rudolf, Rebeka (Author) |
|---|
| Files: |  jmmp-08-00217_(1).pdf (3,23 MB)
MD5: AB56E2CCEAA69538110734802F3D6199
 https://www.mdpi.com/2504-4494/8/5/217
|
|---|
| Language: | English |
|---|
| Work type: | Article |
|---|
| Typology: | 1.01 - Original Scientific Article |
|---|
| Organization: | FS - Faculty of Mechanical Engineering
|
|---|
| Abstract: | A complementary characterisation of the Al-alloy EN AW-5454 was carried out, intended for obtaining the laser hybrid welding parameters of subassemblies in the automotive industry. The investigation included a microstructural examination and the determination of the alloy’s properties using several analytical methods (HV5 hardness measurement, tensile test, Charpy impact toughness, fracture mechanics analysis). Samples were prepared in the longitudinal and transverse directions of a cold-rolled sheet of EN AW-5454 with thicknesses of 3.5 mm and 4 mm. The measured hardness on the thinner sheet was 5% higher than on the thicker sheet. The tensile and yield strength were nominal, while the elongations were smaller by 2.2–3.2% for the longitudinal samples and by 2.7–13.7% for the transverse samples. The smaller deviations from the nominal values are for the thinner sheet metal. A precise topographical analysis showed the brittle fractures of the samples. The Charpy impact toughness results on the thicker plate showed a 20% greater work needed to break it in the longitudinal direction than in the transverse direction. With the thinner sheet metal, 40% greater work was needed. SEM (scanning electron microscope) analysis has shown that the intermetallic Al6(Mn,Fe) particles in the longitudinal samples were mostly intact, with evidence of tough areas on the upper part of the fracture, indicating a better toughness than the specimens in the transverse direction. More crushed intermetallic particles were observed at the fractures of the transverse samples, and their distribution appeared to be more oriented in the direction of rolling. Fracture mechanics SENB (single edge notch bending) tests and their analysis showed that the resistance of the material to crack propagation in the longitudinal sample was about 50% greater than that in the transverse sample. SEM analysis of the fractures showed that the state of the intermetallic particles in the fracture mechanics testing and the fracture mechanism differed from the one in the Charpy fractures. |
|---|
| Keywords: | Al-alloy EN AW-5454, characterisation, microstructure, properties |
|---|
| Publication status: | Published |
|---|
| Publication version: | Version of Record |
|---|
| Submitted for review: | 23.08.2024 |
|---|
| Article acceptance date: | 23.09.2024 |
|---|
| Publication date: | 30.09.2024 |
|---|
| Publisher: | MDPI |
|---|
| Year of publishing: | 2024 |
|---|
| Number of pages: | 20 str. |
|---|
| Numbering: | Vol. 8, iss. 5, [article no.] 217 |
|---|
| PID: | 20.500.12556/DKUM-90887  |
|---|
| UDC: | 621.74:669.715 |
|---|
| ISSN on article: | 2504-4494 |
|---|
| COBISS.SI-ID: | 209670147 |
|---|
| DOI: | 10.3390/jmmp8050217 |
|---|
| Copyright: | © 2024 by the authors |
|---|
| Publication date in DKUM: | 02.12.2024 |
|---|
| Views: | 214 |
|---|
| Downloads: | 24 |
|---|
| Metadata: |    |
|---|
| Categories: | Misc.
|
|---|
|
:
|
Copy citation |
|---|
| | | | Average score: | (0 votes) |
|---|
| Your score: | Voting is allowed only for logged in users. |
|---|
| Share: |  |
|---|
Hover the mouse pointer over a document title to show the abstract or click
on the title to get all document metadata. |
