| Naslov: | Comparison of three methods of measuring residual stresses in welded joints of high-strength steel S960QL |
|---|
| Avtorji: | ID Manjgo, Mirza (Avtor)
ID Lojen, Gorazd (Avtor)
ID Gubeljak, Nenad (Avtor)
ID Karpe, Blaž (Avtor)
ID Vuherer, Tomaž (Avtor) |
|---|
| Datoteke: |  materials-18-00950.pdf (19,91 MB)
MD5: 841CC61F1E1D1B1A4B64F7FD5C457F3A
 https://www.mdpi.com/1996-1944/18/5/950
|
|---|
| Jezik: | Angleški jezik |
|---|
| Vrsta gradiva: | Članek v reviji |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: | FS - Fakulteta za strojništvo
|
|---|
| Opis: | The influence of residual stresses as a result of the welding process in the overall stress state of the weld joint is of great importance because they significantly affect the creation and growth of cracks, the occurrence of brittle fracture, and material fatigue. Previous experiences indicate that it would be necessary to provide an assessment of the deformation and stress state in the critical zones of the weld joints using a suitable test method, which will not endanger the structural integrity of the tested places. There are different methods for measurement of residual stress in welded constructions: destructive, semi-destructive and non-destructive. To choose one method over another, it is necessary to take into account the advantages and limitations of these techniques for practical application. This paper considers and analyzes the residual stresses in the welded joint of high-strength steel S960QL. MAG welding was performed by a robot. Three methods were used to measure the residual stresses: the magnetic method (MAS), the X-ray diffraction method (XRD), and the hole drilling method (HD). By all three methods, the highest residual stresses were measured in the weld metal and in the heat-affected zones. Nevertheless, the measured values differed considerably. The differences can be contributed to (a) the kind of stress that the individual method measures, (b) to the volume of material from which each method captures the signal and averages it, and (c) to the different sensitivities of the applied methods to coarse-grained microstructure and microstructural gradients. |
|---|
| Ključne besede: | welded joints, high-strength steel, residual stress, magnetic method, X-ray diffraction method, hole drilling method |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Poslano v recenzijo: | 27.01.2025 |
|---|
| Datum sprejetja članka: | 19.02.2025 |
|---|
| Datum objave: | 21.02.2025 |
|---|
| Založnik: | MDPI |
|---|
| Leto izida: | 2025 |
|---|
| Št. strani: | 21 str. |
|---|
| Številčenje: | Vol. 18, iss. 5, [article no.] 950 |
|---|
| PID: | 20.500.12556/DKUM-93183  |
|---|
| UDK: | 621.791:539.4 |
|---|
| COBISS.SI-ID: | 239053315 |
|---|
| DOI: | 10.3390/ma18050950 |
|---|
| ISSN pri članku: | 1996-1944 |
|---|
| Avtorske pravice: | © 2025 by the authors |
|---|
| Datum objave v DKUM: | 11.06.2025 |
|---|
| Število ogledov: | 191 |
|---|
| Število prenosov: | 9 |
|---|
| Metapodatki: |    |
|---|
| Področja: | Ostalo
|
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Skupna ocena: | (0 glasov) |
|---|
| Vaša ocena: | Ocenjevanje je dovoljeno samo prijavljenim uporabnikom. |
|---|
| Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
